- Boom switch mounting hardware.
- Display mounting bracket and hardware.
- Display power pigtail (connects to crane power).
- Operator and Installation manuals.
-
The L25 Installation kit includes the hardware needed to mount a boom tip switch and L20D display on a crane. This kit is included with the system. May be purchased for a 2nd crane to allow a system to be used easily on 2 different machines. Content can vary from photo. Includes: -
1) Lithium D-cell battery replacement kit (L2581A) 2) Alkaline battery pack - 3C (L2594-3C) 3) L25 Antenna Replacement kit (L2545) 4) Boom Switch Storage Flag (L2516) 5) Boom Switch Cover (L2618) 6) Eyebolt w/ mounting nut (4" or 6") Call. 7) Boom Switch Transmitter PCB Assembly (L2540A) 8) Boom Switch Gasket (L2508) 9) Antenna Strain Relief (switch - L2258, RX - L2256) -
The standard L25 Radio Anti-Two-Block System includes one RAT Boom switch, receiver, weight & chain, installation kit and manual. It will provide horn and light warning alarms for 1 winch on main or jib. Add the 2nd Winch Kit to protect a second winch. -
L25 Switch, Weight and Chain Kit (Lithium Battery TX) w/ installation hardware -
Call LIFTek for these replacement parts.- Lithium D-cell battery replacement kit (L2581A)
- Alkaline battery pack - 3C (L2594-3C)
- L25 Antenna Replacement kit (L2545)
- Boom Switch Storage Flag (L2516)
- Boom Switch Cover (L2618)
- Eyebolt w/ mounting nut (4" or 6")
- Boom Switch Transmitter PCB Assembly (L2540A)
- Boom Switch Gasket (L2508)
- Antenna Strain Relief (switch - L2258, RX - L2256)
-
These kits supply an external relay and installation instructions for driving existing OEM lockout valves on your crane when retro-fitting the L25 Radio Anti-Two-Block System. These kits, when properly installed, will insure that the L25 actuates your lockouts independently of any existing load system and will not interfere with their operation. -
These kits include some of the basic items we want on hand when installing one of these valves. The kits include 10 feet of oil resistant, flexible SO cable, crimp terminals, cable ties and the installation instructions. (We typically supply one kit per valve, so if you need purchase 3 valves, you would also get 30' of cable and sufficient terminals, ties etc. for 3 valves) -
Rear cameras are used much like a rearview mirror except the operator can get a very wide view of the entire area behind the truck in a single glance. Available in a range of lens angles, rear cameras can provide a wide angle view for general safety when backing or with the correct mounting these cameras can also be used for very precise backing in tight quarters, allowing the operator a view into the blind spot directly behind the truck. A magnetic base makes for a quick and secure mounting that can easily be changed if required. -
Mast cameras - these can be mounted anywhere as needed, but are typically mounted on the side of the forklift mast and provide a general overview of the work area in front of the truck. Often used on trucks with poor visibility in front due to special attachments they are a lower cost option to the fork view as the camera does not move up and down with the fork carriage. Super strong magnets allow these cameras to be mounted with no welding or drilling on the mast. Can be moved as needed. -
The highly adaptable and industry proven VC3 Ball camera is shown here with cushioned magnetic mounts on the L3520- G1 steel camera guard. This guard can also be welded down for maximum camera protection. This camera is nitrogen filled and available in standard 420 TVL or high resolution 700 TVL versions. LIFTek versions of this camera are built with the correct lens and with shock/vibration resistant features for fork lift applications. -
Electric Lift Truck Noise Suppressor -
OTMV Cable - Over the Mast Video Cable