-
Industrial DC-DC Converter; Magnetic Mount Installation Kit (w/ mag keeper) 42mm -
DC-DC Converter/Filter for Electric Trucks - Non-Isolated -
Electric Lift Truck Noise Suppressor -
DC Filter for Electric Trucks and LP Trucks - Non-Isolated Output -
Extra Stage DC Filter for Electric Trucks - Usually required on AC drive systems -
Our Most popular DC-DC Converter/Filter for Electric Trucks -
Replacement cable that can be used on some pulley type camera systems. Industrial continuous flex, oil resistant, shielded. -
Lift Truck Power Cable -
OTMV Cable - Over the Mast Video Cable -
Shows typical D7V cables that run from the display harness to a carriage mounted or mast/rear mounted camera. Coil cable required for carriage camera not shown. -
Shows typical D7K cables that run from the display harness to a carriage mounted or mast/rear mounted camera. Coil cable required for carriage camera not shown. -
LIFTek coil cables are the highest quality available. Proprietary materials and design insure long life and high performance. Properly installed LIFTek coil cables will never sag or stretch and will outlast pulley or cable reel based systems at a lower cost. -
D7V Indoor Mast Camera System -
D7V Load Back Rest Camera System - Provides overview and good fork depth information. -
D7V Back Up Camera System -
Indoor Fork View Camera for Hook Style Fork Carriage -
9" LCD Display 2 Channel (options for 3 or 4 channel) -
7" LCD Display -
The highly adaptable and industry proven VC3 Ball camera is shown here with cushioned magnetic mounts on the L3520- G1 steel camera guard. This guard can also be welded down for maximum camera protection. This camera is nitrogen filled and available in standard 420 TVL or high resolution 700 TVL versions. LIFTek versions of this camera are built with the correct lens and with shock/vibration resistant features for fork lift applications. -
Mast cameras - these can be mounted anywhere as needed, but are typically mounted on the side of the forklift mast and provide a general overview of the work area in front of the truck. Often used on trucks with poor visibility in front due to special attachments they are a lower cost option to the fork view as the camera does not move up and down with the fork carriage. Super strong magnets allow these cameras to be mounted with no welding or drilling on the mast. Can be moved as needed. -
Rear cameras are used much like a rearview mirror except the operator can get a very wide view of the entire area behind the truck in a single glance. Available in a range of lens angles, rear cameras can provide a wide angle view for general safety when backing or with the correct mounting these cameras can also be used for very precise backing in tight quarters, allowing the operator a view into the blind spot directly behind the truck. A magnetic base makes for a quick and secure mounting that can easily be changed if required. -
The highly adaptable and industry proven VC3 Ball camera is shown here with cushioned magnetic mounts. This camera is nitrogen filled and available in standard 420 TVL or high resolution 700 TVL versions. LIFTek versions of this camera are built with the correct lens and with shock/vibration resistant features for fork lift applications. -
The rugged, solid steel CoreCam is built specially for use on certain side shifting fork positioners (SSFP's). Mounting method and brackets vary depending on the SSFP model. -
The Reach Truck CoreCam allows for magnetic or bolt on mounting on the lower cross member of the inner carriage. Provides a clear view for fork insertion and load placement. All powder coated steel and stainless steel construction in the enclosure. -
The camera assembly shown uses the versatile L3319 Heavy Steel Camera Enclosure with the 30G vibration / 100G shock rated KC2 camera. Typically used on deep reach trucks in freezer applications, the camera is heated and has custom lens installed for proper field of view. Mounted by drilling a mounting hole in the lowest cross member (or stringer) of the inner reach carriage. This camera does not extend with the fork carriage. This camera assembly has been used in other applications as well. -
Channel Cams provide an easy and rugged means to mount a camera at fork level. These cameras fit standard ITA hook type fork carriages. A variety of camera options are possible in this series to give your operator the best possible view. Models are available to fit North American class 2A, 3A & 4A. Some European trucks use the B - standard fork carriage (class 2B, 3B, 4B) which is not compatible. -
D7K Mast View Camera System Recommended use: Indoor /Outdoor 12/24/36/48 VDC -
D7K Back Up Camera System Recommended use: Indoor /Outdoor 12/24/36/48 VDC -
D7K Load Backrest Camera System - provides good fork insertion depth and side to side information. Recommended use: Indoor /Outdoor 12/24/36/48 VDC -
D7K Forkview Fork Positioner CoreCam System Recommended use: Indoor /Outdoor 12/24/36/48 VDC CL2 SSFP (Cascade 55K, Rightline ,etc) -
D7K Forkview Channel Camera System Recommended use: Indoor /Outdoor 12/24/36/48 VDC, CL2A, CL3A, CL4A -
This low cost boom tip switch and weight is supplied with or without a custom coiled cable which replaces the spring retracted cord reel. Boom extensions up to 20' are practical. Call LIFTek for information. -
Built for Sky Picker Cranes - this boom tip camera provides a clear view of the load on the ground even 30 stories up. The operator can preset camera zoom levels to quickly adjust the camera from picking at 200 feet and setting at 20 feet. Includes a built in hardwired anti-two-block limiter for this very high speed application. Contact LIFTek for details -
Crown Protection System (CPS) for use with CS3000 or similar core drill rig (CDR). Main and sand line units (right and left side) are available.
