-
Industrial DC-DC Converter; Magnetic Mount Installation Kit (w/ mag keeper) 42mm -
DC-DC Converter/Filter for Electric Trucks - Non-Isolated -
Our Most popular DC-DC Converter/Filter for Electric Trucks -
Extra Stage DC Filter for Electric Trucks - Usually required on AC drive systems -
DC Filter for Electric Trucks and LP Trucks - Non-Isolated Output -
Air lockouts and single lever control kits are also available for lattice cranes. These are used on air control systems which use 1/4" or 3/8" air lines. Typically found on American Cranes. -
Channel Cams provide an easy and rugged means to mount a camera at fork level. These cameras fit standard ITA hook type fork carriages. A variety of camera options are possible in this series to give your operator the best possible view. Models are available to fit North American class 2A, 3A & 4A. Some European trucks use the B - standard fork carriage (class 2B, 3B, 4B) which is not compatible. -
LIFTek coil cables are the highest quality available. Proprietary materials and design insure long life and high performance. Properly installed LIFTek coil cables will never sag or stretch and will outlast pulley or cable reel based systems at a lower cost. -
Crown Protection System (CPS) for use with CS3000 or similar core drill rig (CDR). Main and sand line units (right and left side) are available. -
D7K Back Up Camera System Recommended use: Indoor /Outdoor 12/24/36/48 VDC -
Shows typical D7K cables that run from the display harness to a carriage mounted or mast/rear mounted camera. Coil cable required for carriage camera not shown. -
D7K Forkview Channel Camera System Recommended use: Indoor /Outdoor 12/24/36/48 VDC, CL2A, CL3A, CL4A -
D7K Forkview Fork Positioner CoreCam System Recommended use: Indoor /Outdoor 12/24/36/48 VDC CL2 SSFP (Cascade 55K, Rightline ,etc) -
D7K Load Backrest Camera System - provides good fork insertion depth and side to side information. Recommended use: Indoor /Outdoor 12/24/36/48 VDC -
D7K Mast View Camera System Recommended use: Indoor /Outdoor 12/24/36/48 VDC -
D7V Back Up Camera System -
Shows typical D7V cables that run from the display harness to a carriage mounted or mast/rear mounted camera. Coil cable required for carriage camera not shown. -
Indoor Fork View Camera for Hook Style Fork Carriage -
7" LCD Display -
D7V Load Back Rest Camera System - Provides overview and good fork depth information. -
D7V Indoor Mast Camera System -
9" LCD Display 2 Channel (options for 3 or 4 channel) -
The camera assembly shown uses the versatile L3319 Heavy Steel Camera Enclosure with the 30G vibration / 100G shock rated KC2 camera. Typically used on deep reach trucks in freezer applications, the camera is heated and has custom lens installed for proper field of view. Mounted by drilling a mounting hole in the lowest cross member (or stringer) of the inner reach carriage. This camera does not extend with the fork carriage. This camera assembly has been used in other applications as well. -
Hydraulic Lockout Valve Assy (15 gpm, 5000 psi, SAE8 1/2" ports, w/ Manual Override, 12V 28W Coil, DIN field wireable connector, 5.6" x 3.4" x 1.5") -
These 3000 psi valves are used to shut off crane functions on hydraulic cranes during a two-block (or overload) condition. Used on winch up, telescope out, boom down. They automatically allow corrective action: winch down, telescope in, boom up. -
This section explains how to specify the size, number and voltage of lockout valves for your crane. These valves will most likely NOT be needed if your truck already has a factory installed anti-two-block system. The L25 will drive those valves. Please check with us to see if a relay kit might be needed. -
Hydraulic Lockout Valve Assy (12V, 40gpm, 5000psi, 16SAE ports Alum body) -
This low cost boom tip switch and weight is supplied with or without a custom coiled cable which replaces the spring retracted cord reel. Boom extensions up to 20' are practical. Call LIFTek for information. -
L20 A2B System - discontinued 2004 Most parts and service available. -
USTC Cranes were supplied with L20 and L25 Radio A2B Systems. Parts and service is available for these units. Boom transmitter switch and power pigtail may vary. Please provide model and serial number from these units when ordering parts. -
L25 Radio A2B systems supplied on certain model Jomac and Skypicker Boom Trucks. Compatible parts and service are available for the units. Power pigtails (connection to the truck power) can vary. Please confirm your type when ordering. See the photo showing the 3 types. -
L25 Radio A2B systems supplied on certain model Manitex Boom Trucks, Manitowoc Boom Trucks, and Skycranes from Nov 2000 to the present. Compatible parts and service are available for the units. Power pigtails (connection to the truck power) can vary. Please confirm your type when ordering. See the photo showing the 3 types. -
L25 Radio A2B - used on digger derricks An anti-two-block is now required by OSHA when using a digger derrick for regular crane work. Only pole handling is exempted. This L25 includes a special weight and chain which reduces wear when used with synthetic rope. Weight is painted black -
LIFTek offers the following versions of the boom tip transmitter switch. L25RS-1E Standard RAT Switch - with lithium D-cell. 5+ year battery life. This is the standard product for North America. L25RS-2 3C version - uses an alkaline battery pack for international shipping. Estimated battery life 2.5 years. L25RS-3 SW Saltwater version with lithium D-cell, sealing boot on switch plunger. (Override flag cannot be used). L25RS-4 3C+SW Saltwater version with 3C alkaline battery pack.
